Insulating glass machine customization-manufacture,factory,supplier from China

The factors that affect the quality of insulating glass equipment are mainly the selection of raw materials and the manufacturing process. The quality of these raw materials directly affects the quality and service life of insulating glass.When the glass material is known, such as ordinary glass or tempered glass, the fracture strength of the original glass can be determined according to the glass strength design theory. Because the glass produced by the insulating glass machine is composed of two (or more) pieces of glass, the perimeter is sealed to form a sealed airtight layer.

insulating glass production process includes the following key steps ‌ :‌ Preparation and treatment of original glass ‌ : First of all, choose high-quality original glass, usually float glass, embossed glass, heat-absorbing glass or tempered glass. The thickness of the glass can be selected according to the demand, such as 3, 4, 5, 6, 8, 10, 12mm and so on. The glass needs to be cut by the glass cutting machine, the glass edging machine, the glass cleaning machine and the drying process to ensure that the surface is clean and scratch free.

Insulating glass, also known as double-glazed or triple-glazed glass, is widely used in modern architectural designs for its thermal insulation and soundproofing properties. To maintain the clarity and aesthetics of insulating glass, regular cleaning is essential. This is where the insulating glass cleaning machine comes into play.The insulating glass cleaning machine is a specialized equipment designed for efficiently cleaning the interior and exterior surfaces of insulating glass units.

‌ The production process of insulating glass includes the following main steps ‌ :‌ cutting glass ‌ : Use a glass cutting machine to cut the original glass to the appropriate size according to the required size, ensuring that the size is accurate and the edges are neat.‌‌ glass ‌ : The cut glass needs to be cleaned by a glass cleaning machine to remove dust, oil and other impurities on the surface and ensure that the surface of the glass is clean and tidy.‌ Making spacer frame ‌ : The spacer is cut according to the required size by using an aluminum bar bending machine, then bent into rectangl

The maintenance and upkeep of the fully automatic insulating glass production line is a task that we need to pay attention to for a long time. Only by maintaining the insulating glass equipment well can we reduce unnecessary troubles in the work. Routine maintenance and upkeep of the machine is very important. You should always observe the moving parts, water system, air system, and electrical system of the machine. If there is any abnormality, stop the machine immediately for inspection.1.

Insulating glass production line operating procedures of the main steps and precautions1.‌ Preparation ‌ :① Open the total power supply and air source of the insulating glass production line.② The water tank of the cleaning machine is filled with water, and the water heater is turned on in winter.③ Turn on the insulating glass equipment transfer, inspection lamp, fan, brush, water pump ‌.2.‌ Procedure ‌ :① Put the glass into the feed section of the insulating glass production line with a glass lifting machine or a fully automatic loading and unloading machine.② The glass enters the cleaning an

The sealing and structural stability of the insulating glass system are achieved by insulating glass glue. Insulated glass is always faced with the influence of external water vapor penetration and temperature changes during its service life. Therefore, the insulating glass glue must first be able to prevent external water vapor from entering the air layer of the insulated glass. After insulating glass is installed, it often faces the influence of external forces such as temperature differences, air pressure, and wind loads.

(1) After the insulating glass is filled with argon, the pressure difference between the inside and outside can be reduced, the pressure balance can be maintained, and the glass explosion caused by the pressure difference can be reduced.(2) It can effectively improve the K value of the insulating glass, reduce the condensation of the indoor glass, and improve the comfort level.

How much money is needed to start an insulating glass processing plant depends on the equipment purchased, if it is a fully automatic production line, it is usually around 300-1,000,000 yuan.With the output of processing 1000-2000 square metres per day, the daily profit is around 10000-35000 yuan (the larger the area the more profit).1. Insulating glass processing cost: around RMB 18-25 per square metre, plus RMB 3-5 per square metre for labour. The cost is around 21-30 RMB.2.

Through the automatic insulating glass inflator, after filling the glass with argon, the following effects can be achieved:(1) Argon can reduce the internal and external pressure difference, maintain the pressure balance, and reduce the glass explosion caused by the pressure difference.(2) After argon is filled, the K value of the insulating glass can be effectively improved, the condensation of the indoor side glass can be reduced, and the comfort level can be improved, that is, the aerated insulating glass is less prone to dew and frost, but the non-aeration is not the direct cause of fog.(3